black ugg trainers How To Drill Your Own Water Well

very cheap ugg boots for sale How To Drill Your Own Water Well

There something that our ancestors all had on their property, which we don often have today. No, I not referencing a barn, although that would be true. I referring to a well.

City water is something relatively new, at least as we know it. Before that, people had to rely on well water for everything. If they didn live close enough to their neighbors to share a well, they had to have their own.

Today, having a well is rare. Few can afford the cost of having a well commercially drilled and even fewer try doing it themselves. But there are ways of doing it yourself, without having to resort to the time tested method of using a pick and shovel.

The problem with using a pick and shovel to dig a well, besides it being back breaking work, is that the well has to be big enough to climb in and work. That means displacing a lot more dirt in order to get down to the level of the water. The well also has to be shored up as you go, in order to prevent it from caving in while you are working.

This Ultra Efficient Water Filter Fits In Your Pocket And Removes 100 Percent Of Water Borne Bacteria!

But there is an easier way. You can actually drill a well fairly easily, using nothing more than PVC pipe and water. No, I didn invent this way, someone else did; but his method is so simple, it deserves to be shared.

To start with, you have to have the right soil. Not all soil is created equal and the wrong soil will make it extremely hard to drill a well. The ground beneath our feet is divided into layers, and the composition of those layers will drastically affect how easy they are to drill through. We can have layers of:SandRockSoil and sand are really the only ones which are easy to drill through. Of course, if there are tree roots in the midst of the soil, you may have trouble drilling through them. Clay breaks up very slowly, and rock and gravel well, they speak for themselves.

Water is caught in the layers of sand and gravel. So you eventually want to hit one of them, preferably sand. If you hit gravel with water in it, it could cause problems, as you actually have to get down into the layer to have a good water flow.

In much of the country, water can be found in a sand layer as little as 20 feet below the surface. Professional well drillers won stop there, as they want to make more money and they charge by the foot. Besides, generally speaking, deeper water will be better quality water.

The PVC drill is extremely easy to make. All you need is some two inch PVC pipe and some fittings. The bit itself is made out of the pipe, by cutting it. This can be done with just about any type of saw, but it is most easily done with a grinder.

In reality, all this is going to do is scrape at the dirt, breaking it up so that it can be removed from the hole. But that all it needs to do. You will be pumping water down that hole as well, which will be constantly flushing it out, removing the dirt and sand that the drill point is breaking up.

The same thing can be made out of galvanized plumbing pipe. That will stay harder,
black ugg trainers How To Drill Your Own Water Well
allowing you to drill through tree roots and even some soft rocks.

This same PVC pipe can serve as your well casing with some minor adjustment. All wells need a screen at the bottom. The purpose of this screen is to allow the water to seep through the casing, while keeping the sand out. To make your pipe function as a well screen also, cut a number of thin slits in the side of the pipe, staggering them, so that you don weaken the pipe. This is most easily done with a pneumatic die grinder or cut off tool (they are essentially the same) and a small, very thin cut off tool blade.

Remember, you don want to weaken the pipe, so put about six slots in the pipe, lengthwise around the circumference of the pipe. Then move up five or six inches and do it again. Make sets of slots like this for the bottom three feet of your drill pipe.

The other end of the PVC pipe needs to be adapted to attach two garden hoses. It takes two in order to have enough water coming into the drill to force the debris that I was just talking about, out of the hole. One hose won be enough. In fact, one of those hoses should be coming from a neighbor house, so that both of them will have a full flow of water.

The well head consists of a two inch PVC with adapters on both sides stepping it down to an inch garden hose connections. Make sure that all connections are put together with PVC cement and primer, so that they don come apart. The rubber coupler is used, rather than a fixed connection, so that another section of PVC pipe can be added, when needed.

This is where the water will enter the drill, so that it can flush out the hole. The water will travel down the length of the drill, inside the pipe and come out the bottom. It will travel up the outside of the pipe, enlarging the hole slightly and carrying the debris from the well out.

The only other thing you need is a handle. You are going to be the for this drill, so you need to turn the pipe back and forth, causing the drill teeth to break up the soil. A simple piece of wood to cross the pipe will serve fine. You may want to round the edges and sand it, to make it easier on your hands. Then, attach it to the pipe with large hose clamps.

New Solar Backup Generators Deliver 4 Times More Power Than Other Models!

It will become important to be able to move your handle up the length of the pipe as the pipe descends into the hole. Otherwise, you won be able to keep drilling. So, don do something like using a PVC cross to make the handle permanently attached to the drill pipe.

If you have a post hole digger, you might want to start the hole for your well with that. That will cut through grass roots much easier than the PVC drill will, getting your hole started. Then, when you stand the drill up and put it in the hole, the hole itself can help hold it up.

To drill the well with this simple drill, start by connecting the hoses and turning on the water at both sources. Then put the bit end of the drill in the hole, standing it up. Adjust the handle height, if needed, so that it is at a comfortable working height. That would be somewhere between your upper chest and slightly below your waist. Any farther up or down will add strain to your body while drilling.

Start turning the drill back and forth, about a quarter turn in each direction. You will see muddy water start to bubble up out of the hole. Get used to looking at that mud, as you see it for the next few hours. The drilling action is slow, but not really any slower through dirt and sand than what I experienced using an air driven drill.
black ugg trainers How To Drill Your Own Water Well